-40%

XBee-PRO ZB S2B ZigBee Module, 63 mW, U.FL Connector

$ 17.95

Availability: 100 in stock
  • Condition: New
  • Item must be returned within: 14 Days
  • MPN: 9243
  • Brand: Unbranded
  • Refund will be given as: Money Back
  • All returns accepted: Returns Accepted
  • Return shipping will be paid by: Buyer

    Description

    XBee-PRO ZB S2B ZigBee Module, 63 mW, U.FL Connector
    XBP24BZ7UIT-004
    Wireless connectivity using the ZigBee protocol
    XBee-PRO ZB S2B embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors.
    Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.
    Series 2 modules use a different hardware configuration from the earlier models. They are not compatible with the outdated ZNet Series 2.5 modules.
    ZB Series 2 New Features
    ZB offers many new and improved features over ZNet 2.5, including:
    Data transmissions are resolved directly to APS unicasts. This provides the ability to send and receive ZDO commands.
    NH
    command configures the unicast transmission timeout. This command can extend the number of unicast hops dramatically beyond the 6-8 hop limit that existed in ZNet 2.5.
    ZS
    command allows ZigBee stack profile to be set as required.
    Routers and coordinators can expire end-device children from their child tables if the end device has not polled within a settable timeout.
    The
    ZA
    command is no longer needed.
    SE
    ,
    DE
    and
    CI
    addressing commands are always enabled.
    AI
    now includes several new values.
    Note: This module is certified for use in North America and Australia only. It is permissible to use in most of Europe if you set the PL command to 0, reducing the power output to 10 mW / 10 dBm. This module cannot be used in Japan under any circumstances; the Japanese market has a specific 10mW-max variant. See the User Manual for specific restrictions and end-product label requirements. Other areas, check local regulations.
    ZB S2B ZigBee Module Features
    Power output: 63mW (+18 dBm)
    Indoor/Urban range: Up to 300 ft (90 m)
    Outdoor/RF line-of-sight range: Up to 2 miles (3200 m)
    RF data rate: 250 Kbps
    Interface data rate: 1200 bps to 1 Mbps (non-standard baud rates supported)
    Receiver sensitivity: -102 dBm
    Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
    Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
    Error handling: Retries and acknowledgments
    Channel capacity: 15 Direct Sequence Channels (11 through 25)
    Addressing: PAN ID, 64-bit IEEE MAC
    Encryption: 128-bit AES
    Supply voltage: 2.7V - 3.6V DC (Footprint Recommendation: 3.0V - 3.4V DC)
    Transmit current: 205 mA (@ 3.3V)
    Receive current: 47 mA (@ 3.3V)
    Idle current: 15 mA
    Sleep current: 3.5 µA typical @ 25°C
    Frequency band: ISM 2.4 GHz
    Interface options: 3V CMOS UART, ADC, DIO
    Configuration method: AT and API, local or over-air
    Digital I/O: 10 I/O lines
    ADC: Four 10-bit analog inputs
    Size: 0.960 in × 1.297 in (2.438 cm × 3.294 cm)
    Weight: 0.10 oz (3g)
    Operating temperature: -40°C to 85°C (industrial)
    Certifications: FCC (USA), IC (Canada), ETSI (Europe), C-TICK (Australia)