-40%

XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Chip Antenna

$ 16.89

Availability: 100 in stock
  • Refund will be given as: Money Back
  • MPN: 9243
  • Brand: Unbranded
  • Item must be returned within: 14 Days
  • Return shipping will be paid by: Buyer
  • All returns accepted: Returns Accepted
  • Condition: New

    Description

    XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Chip Antenna
    XBP24-DMCIT-250
    Wireless connectivity using the DigiMesh protocol
    XBee-PRO DigiMesh 2.4 delivers end-point device connectivity with a widely deployable
    2.4 GHz
    transceiver. These modules use the innovative DigiMesh networking protocol. This innovative, peer-to-peer protocol offers users added network stability through self-healing, dense network operation and support for sleeping routers, extending the operational life of battery-dependent networks.
    Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.
    The XBee-PRO 2.4 DigiMesh modules use the same hardware as the XBee-PRO 802.15.4 modules. It is possible to change from one platform to the other by loading different firmware onto the same module.
    Note: This module is certified for use in North America and Australia only. It is permissible to use in most of Europe if you set the PL command to 0, reducing the power output to 10 mW / 10 dBm. This module cannot be used in Japan under any circumstances; the Japanese market has a specific 10mW-max variant. See the User Manual for specific restrictions and end-product label requirements. Other areas, check local regulations.
    DigiMesh Protocol
    DigiMesh is a proprietary mesh networking protocol. Its features include:
    Self-healing
    — Any node may enter or leave the network at any time without causing the network as a whole to fail.
    Peer-to-peer architecture
    — No hierarchy and no parent-child relationships are needed.
    Quiet protocol
    — Routing overhead will be reduced by using a reactive protocol similar to AODV.
    Route discovery
    — Rather than maintaining a network map, routes will be discovered and created only when needed.
    Selective acknowledgments
    — Only the destination node will reply to route requests.
    Reliable delivery
    — Reliable delivery of data is accomplished by means of acknowledgments.
    Sleep modes
    — Low-power sleep modes with synchronized wake-up are supported, with variable sleep and wake times.
    2.4GHz DigiMesh Module Features
    Power output: 63mW (+18 dBm)
    Indoor/Urban range: Up to 300 ft (90 m)
    Outdoor/RF line-of-sight range: Up to 1 mile (1.6 km)
    RF data rate: 250 Kbps
    Interface data rate: Up to 115.2 Kbps
    Receiver sensitivity: -100 dBm
    Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
    Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
    Error handling: Retries and acknowledgments
    Channel capacity: 12 Direct Sequence Channels
    Addressing: PAN ID, channel, and 64-bit addresses
    Encryption: 128-bit AES
    Supply voltage: 2.8V - 3.4V DC (Footprint Recommendation: 3.0V - 3.4V DC)
    Transmit current: 250 mA (@ 3.3V)
    Receive current: 55 mA (@ 3.3V)
    Sleep current (pin sleep): <10 µA
    Sleep current (cyclic sleep): <50 µA
    Frequency band: ISM 2.4 GHz
    Interface options: 3V CMOS Serial UART (5V-tolerant inputs)
    Configuration method: AT and API
    Digital I/O: 13 I/O lines
    ADC: Six 10-bit analog inputs
    Size: 0.960 in × 1.297 in (2.438 cm × 3.294 cm)
    Weight: 0.10 oz (3g)
    Operating temperature: -40°C to 85°C (industrial)
    Certifications: FCC (USA), IC (Canada), ETSI (Europe), C-TICK (Australia)
    Above specifications assume usage at full power. For Europe @ 10mW, see user manual.